I’ve just returned from a two-week vacation on the east coast of Canada and am more than ready to tackle the LFJ #3. Now that I have the fabric and the lining, I’m all set to get that pattern ready for the first (and I hope the final) muslin fit garment.
I’ve been down this route before, but the second time I made one of these jackets I used the same pattern as from the first so was able to skip much of this fitting activity. This time, I’ve chosen a different pattern.
My first and second jackets were both Vogue 7975, a basic design and one that is very easy to create if using the regular lining approach. I liked its open front and two-piece sleeves which I made three-quarter length in LFJ #1 and full-length in LFJ #2. This time I wanted to do something different, and as I mentioned in a previous post, learn a few new things. So this time I’ve selected Vogue 8804, a pattern created by Claire Schaeffer who wrote the book (really she did) on making the ‘Chanelesque’ jacket.
So, what do I like about this pattern that makes it different/upgraded from V 7975:
- This one has a three-piece sleeve, a real upgrade in my view. A two-piece sleeve provides the opportunity for a better, slimmer fit than the one-piece, and my research tells me a three-piece one is even better. And it just looks good.
- The sleeve has a buttoned vent. Need I say more?
- This pattern uses hand-worked button holes, a real couture technique. I’m excited if a bit daunted never having done them before, but I’ll get the supplies and give it a try.
- It has four pockets rather than two. Many Chanel jackets have four pockets – but certainly not all. This feature does, however, make it different than my last two and who wants three jackets all the same?
- The design employs an underarm ease for bust shaping. I think this may be a good idea, but that remains to be seen.
- And, although the back does not have princess seams, it does have a centre back seam as well as side panels without an actual side seam for better shaping.
So, I’m ready to begin. Well, first I read a few online reviews of this particular pattern and most suggest that it’s a bit boxy (although it doesn’t look that way on the line art) and it runs slightly large. I’ll consider this with the first fitting.
I take out all the pattern pieces and Claire Shaeffer’s instructions which are, to say the least, detailed. This pattern was designed specifically for this kind of Chanel-like construction process so the instructions reflect that. I note that there are trim guides for cutting and shaping the trim, a little extra that I will ditch. I’ve never had trouble cutting or shaping trim so I think this is unnecessary. Back in the envelope.
She has also provided a back interfacing guide. I’m inclined to think that I’ll use the French Jacket interior approach that I’ve used be for with terrific results: I’ll use my trusty twill tape and/or silk organza selvedge to stabilize the neck, hem, sleeve and front edges. Back interfacing guide: back in the envelope. There is a pattern piece of interfacing of the bottom of the sleeves that I’ll consider since this jacket has a button placket on the sleeve vent.
Right out of the pattern envelope I realize that there will be little tissue fitting to begin the process – there are simply too many seams. I pin the seams as best I can; I also pin the dart ease then compare the pattern’s high figure point to the HFP on my own bodice block. Although I give it a brave attempt and get a sense, it’s a bit ragged to tell you the truth — the fitting, that is! I note that the upper chest area is a bit too short for me (a typical commercial pattern problem) so I lengthen it before beginning. I also note that, contrary to a Chanel-type design, the waist-line is a bit too low, so I raise it slightly. According to the Chanel videos, this raised waist-line provides for a better fit. Now I’m ready to get at the muslin.
I decide to use Susan Khalje’s couture technique and begin by going around every pattern piece marking the seam lines carefully. There was a time when commercial patterns had these marked: this was before the advent of the multi-sized pattern. In any case, I will work with seam lines (which I will thread trace) rather than seam allowances as they do in real couture houses so I’m told. Of course, intuitively it just makes sense that matching seam line to seam line rather than seam allowance edge to seam allowance edge will be more accurate and provide for a better fit.
Now that all the seam allowances are marked, I can lay out the pattern on my muslin fabric for cutting. I pin carefully, take great pains to “respect the grain” as Susan Khalje reminds us so often. The pinning takes time, but the cutting – not so much! I love this rough cutting. The seam allowance edges are immaterial in this approach since I’ll be marking all the sewing lines and using those.
Once I hack (cut) out the pattern pieces, I’m ready for the all-important marking. Stay tuned!
You must be logged in to post a comment.